Concrete Pumping Contractor Bonita
Yes, It’s Possible: Trailer Pump Can Be Used for Concrete Pumping in Bonita
It seems that people cannot quite agree on many things about concrete pumping in Bonita, so let us give you an expert’s opinion. We are here to explain how things work in complete detail. Unknown to many, cement can be pumped using trailer-mounted pumps. We made such a sensible notion a reality by using proper equipment and developing new systems.
Before we share how we were able to achieve this, allow us to envision a big hose with concrete streaming out towards one end. We are able to do this by adding priming materials on the concrete to make it run through the hose smoothly. Our team uses a priming agent to improve the viscosity of the mixture. In a test, we found out that a lump consisting of three rocks can slide smoothly through a hose with a three-inch diameter together with the portland cement, water and sand.
Given this, there’s a likelihood that the concrete would be able to go through smoothly. In an actual operation, the procedure could be hampered by blockages inside the hose. There are instances when blockages or similar matter occurs. Otherwise, you may want to consider using the large hose. To be sure that the flow of concrete would go smoothly, you can even try a hose with a diameter of four inches or bigger.
Because the hose is heavier with the bigger volume of concrete flowing through it, the operator holding the tip of the hose may find it hard to keep it steady. The bigger load is going to wear the tip hose operator out eventually, the reason for the hooks. However, the problem with having a bigger hose is that its weight will impact on the operation.
Count on us to render the needed service, whatever the situation is. We know these things because we are specialists in rock concrete pumping. Our team specializes in providing concrete pumping for big rocks. We have the skills plus the equipment needed to handle your requests.
Concrete Pumping in Bonita Done Professionally
You can use our concrete pumping services for your commercial, residential or industrial projects. We have been in the construction business for over 20 years and have trained an elite group of operators who have worked on numerous projects using trailer pumps. You can make use of our services in a wide range of projects, even the more complex ones. Our services are completely guaranteed, which benefits both of us.
Our team of professionals will make sure that correct procedures are followed during the concrete pumping to assure the safety of everyone in the project site. We take pride in our extensive collection of line pumps which enables us to handle rocks, grouts, pea rocks of up to one inch in diameter. We provide only the first-class array of line pumps. With this, we are able to draw out rock, grout or pea rock in all sizes up to an inch in diameter.
Long Distance, Big Rock Concrete Pumping
The minimum length of hose we usually offer is 200 feet, which is more than enough for most projects. But, we also have the means to cover longer lengths, some measuring up to 1,250 feet. We mostly use hydraulic trailer pumps for long distance and big rock concrete pumping projects, which have the capability to pump 70 cubic yards an hour.
Retaining Wall
Call us and our team will sit down with you to talk about your specific requirements. Be it for decorative purposes or to strengthen commercial or residential foundations, our certified experts can handle the job with utmost efficiency. We have many years of experience behind our back, and we are confident that we can deliver your retaining wall requirements to your satisfaction.
House Lintel Pumping
Our price covers 50 boards on the walls, and these can provide about 50 clean outs, We can also provide an estimate for larger requirements; you only have to inform us, and we will talk about your specific requirements further. We always make it mandatory to check the down cells if they can handle the filling. Then, we put the mixer in place and our technicians carefully inspect the truss straps. With ‘j bolts’ carefully placed in the garage header, and the wall and ground scraped. Rest assured that we will not take off the boards and the nails without a thorough look at the inspection hole.
Columns, Slabs, Tie Beams, Preform Columns, and Sauna Tubes
Our professional concrete placement team will work closely with you and your contractors to ensure foolproof and affordable solutions.
Power Jacking and Sink Holes
Our pumps come in different power capacities, the most powerful of them all yield a power of 4,000 PSI for void filling of the highest quality. It does not matter if the void is under a slab or beneath a building, we have the knowledge, the skill, and the equipment to treat the problem.
Choose Us
There is absolutely nothing simple about concrete pumping. It matters greatly to have the most modern equipment, and the proper knowledge to use such equipment. Concrete Pumping Services is your No. 1 choice when you want proven results. We have a full range of equipment to meet your specific needs, and our incredible team of professionals is always available to deliver the service that you require.
How Our Concrete Pumping Services in Bonita Can Help You
We at Concrete Pumping Services have the equipment, experience, and personnel to cater to your needs. Beyond that, we have the technical skills to carry out industrial, commercial and residential projects. What makes us even stronger is our proven expertise combined with our extensive inventory, which enables us to provide the best possible service to our clients. In case you want to know how we can address your masonry requirements, call or email us. If you’re keen on knowing how we can meet your needs, just give us a call or write to us via email. We would be glad to answer all your questions.
Concrete Pumping Service in Bonita: Best Equipment, Best Manpower
There is only one thing that has moved us, and continues to move us, and that is our commitment to serving your best interest. We have the right equipment to cater to your individual needs, highly trained experts to do the job, proficient procedure and with due consideration to safety.
What Can We Do?
We take pride in having powerful state-of-the-art pumps in the hands of highly trained experts who are able to provide services that will even exceed your expectations. You need not worry about machine breakdowns slowing down your project. We have a well-stocked repair facility where we can restore machines to their prime condition in case the first signs of trouble develop. We have different kinds of trailer pumps from such makers as Schwing, Mayco, Putzmeister, and Reed. We have various models of trailer pumps from such manufacturers as Schwing, Mayco, Putzmeister, and Reed. They are always in tip-top condition because they are well maintained and serviced regularly to avoid sudden breakdowns. In case one pump develops problems, we always have a replacement unit that can be used to prevent work stoppage and project delays. Because of their broad experience, our specialists have figured out how to resolve issues at the slightest sign of trouble. We also have backup equipment to ensure that we can deliver our services on time. Over the years, our team has experienced working with a wide range of situations. Be it a repair or a concrete pumping request, you can count on us to deliver best-value deals.
Take comfort in knowing that we come fully insured, which means to say, we have you, and our duly certified personnel, covered by insurance.
Effectiveness of Trailer Pumps in Cramped Spaces
The idea of using trailer pumps for pumping concrete to a slap may seem far-fetched to some people. If only they realize that pumps of this kind can handle big rocks just as well as boom pumps can. No doubt, boom pumps are very powerful tools, but where space is an issue, they may not make a smart choice.
Our trailer pumps can deliver grout mixed with pea gravel and even bigger stones. They are becoming more popular in the U.S., South America and even Europe. They are becoming more popular in the U.S., South America and even Europe. This type of pump provides high pressure to ensure that the spaces underneath the slabs are filled.
Trailer Pump Power
Trailer pumps are highly recommended for renovation projects, most especially if you need to pump concrete within a 1000-feet distance. You may also use trailer pumps for up to 300-feet high properties. They can even work with as much as 70 cubic yards an hour in nearly all cases. While a model may slightly differ from one to the other, it’s likely that they come with the same boom pumps to pump kits and may weigh as much as 10,000 pounds.
Benefits of Using a Trailer Pump
Many of our customers have started using our trailer pumps, doing away with boom pumps even if they have the space for those machines. The reason for this is that they have realized that trailer pumps are easier to handle. First of all, they are easier to operate. They also leave minimal waste. They can be operated even in a cramped location. Best of all, the cost of using them is comparatively low.
You see, with boom pumps, a large amount of concrete is left behind, converting to around one yard of waste material. Taking it out of the unit usually requires $160 every time. It does not appear practical, if we have to say it, especially if you consider the cost of the unit itself.
With a trailer pump, on the other hand, the waste materials are not that much, which means you get more for your project.
Which Option is Best For You?
Obviously, there are pros and cons to each method. The technology used by most commercial pumps today is amazing so if there are differences, they are not significant enough to make a dent in your wallet. The choice may ultimately hinge on whether you want to save money. If that is the case, then the use of trailer pump is your best choice.
Gunite versus Shotcrete
Gunite is a type of construction material used in constructing pools. Gunite is a mixture of cement and sand (also called mortar), which has played a major part in the swimming pool industry. The method of application requires a high-capacity hose and powerful compressor.
Unlike the shotcrete mixture, gunite requires a lot of skills and attention from the workers because the ratio of the components plus the air pressure used to spray the mix should remain consistent all throughout the project. If the mixture is not properly made, the resulting concrete may not last long.
Deviation, no matter how small, in the mixing of dry materials and water causes a reduction in the pressure rating, which is set at 2,000 psi. You will need to do the Coring tests to check for any signs of inconsistencies. Otherwise, the walls of the pool will crack or worse, cause major water leaks.
Shotcrete is the answer to your gunite problem.
All irregularities of gunite are ruled out through the use of a computer-controlled blend from a concrete batch plant where concrete is fabricated using strict guidelines. The wet material, concrete, is pumped through a two-inch hose to a spout with an air-ring, enabling it to stick to vertical walls. The portions are thoroughly regulated by a program so each truckload contains the perfect ratio of ingredients. The concrete dry mix is then combined with water and pumped via a two-inch sized hose with an air ring. The mix will adhere to the walls once you start to spray it.
The strictly regulated production of shotcrete is the reason why the California Division of Transportation has chosen such product in the building of bridges, roads and seismic retrofits. With shotcrete you are guaranteed that the walls of your pool have a constant strength of 3,000 to 4,000 psi, thus preventing leaks and cracks from happening. By using shotcrete in pool construction, leaks will be highly unlikely. Choose shotcrete because it is accurate and exact; no more guessing games.
Pools
Most of our work is done in building residential swimming pools. We have done numerous pool projects in the San Diego area, earning for ourselves the expressed satisfaction of our clients. Our team has created several pools all over San Diego, California, and all of our past clients were very happy with the end product. Through the years, our company has been using shortcrete to make our clients’ pools, so we know for a fact that this is the best mixture to use.
In addition to building pools, we have also been active in assisting homeowners who want to subcontract the work so they can make their own pool for years. We offer recommendations when requested and answer any inquiries concerning shotcrete that will help people in accomplishing the project that they exactly have in mind.
Pools have seen extensive improvements through the years. Some of the newly built ones have more complex features such as vanishing edges, waterfalls, and fancy rocks. We have mastered our craft and we can very well build the pool that you have in mind.
Drainage Ditches
The drainage ditch is basically a concrete duct that drains off the sewage or excess water. Typically, the ditch has a width of two feet and depth of one foot. It’s made of 3-6 inches of concrete. There is also a type D ditch, measuring 3 feet wide, and there is the trapezoid ditch, as well, that is recommended for commercial use.
And, then our team proceeds with the setting up a wire mesh measuring 6x6x10x10 or the 17gage wire mesh, whatever is appropriate. After digging the soil, our technicians will put either a 6x6x10x10 wire mesh or 17-gage wire mesh depending on the predefined requirements. Our specialists will then pour shotcrete to form the walls of the ditch. Whether you are a contractor yourself or a homeowner, you can count on us to deliver the needed serve to your utmost satisfaction. We work in the presence of both contractors and homeowners so that they could see for themselves how we are able to achieve excellent results.
Erosion Control
In building ditches, we guarantee that there will be no erosion by ensuring that the slopes are well protected. We do this by applying shotcrete on the walls in differing thickness, even without reinforced steel bars. We work in basements and other areas of the house where the foundation is poor. Slopes with vertical embankments are shotcreted with a rough finish, taking the shape of the slope. There is another slope type which you may often see in commercial applications, but may also be used in residential homes. Slopes of this kind are usually fine-graded, with wire mesh. We also use shotcrete in commercial projects to strengthen bridges and roadways. We can also do this in residential projects. This way we are able to build fine-graded slopes with wire mesh in various forms and with a smooth or broom finish.
Gunite or Shotcrete?
Overall, gunite has taken a backseat to shotcrete in terms of efficiency and stability. But gunite can also serve its purpose in select projects because the procedure is cheaper, at least initially. This material is produced using higher air pressure to make the cement harder and tougher. We sometimes use quickening agents to help in the overhead placement of shotcrete.
Guniting and shotcreting are nearly identical. Gunite was first used in the early 1900s. The technique used air pressure to apply mortar on walls, which were thinner than the ones we have now.
The pressure from the jet presses the material to the surface. Quick drying products like Rediset also accelerate the drying process because it solidifies in a matter of hours. The dry-mix type of shotcrete is considered more durable and the one preferred by most users.
The dry-mix procedure is as follows:
(a) Mix the cement and sand thoroughly.
(b) The mixture is then placed into a device called a “gun”.
(c) The feed wheel within the gun meters the mixture.
(d) The compressed air carries the material to a special nozzle through the delivery hose. Through the nozzle’s perforated manifold, the water is sprayed to combine wih the mixture of sand and cement.
(e) The resulting wet mortar is released from the nozzle at high velocity to be gunited.
The Wet-Mix Process
In the wet-mix process, the concrete is blended with water just like in ordinary cement mixing. It is then passed through the conveyance pipeline to the spout, where it is pushed by compressed air at high pressure onto the surface.
By and large, the wet-mix process has been set aside since the dry-mix process yields better results. The dry-mix methods utilize fast or low-speed processes. The lower speed gunite, on the other hand, is passed through using a big hose for bigger concrete load yield. The concrete compunction is less under this process.
Benefits of Wet and Dry Process
Although it is conceivable to get more exact control of the water/cement proportion with the wet process, the fact that this proportion can be kept very low with the dry process negates the complaint of the absence of precise control.
Pumping light-weight aggregate content is best done using the dry process. It must be pointed out that the dry process depends a lot on the water content of the sand. Excessively wet sand causes obstruction inside the conveyance pipeline, a problem that does not happen in the wet process.
The fact that the dry process is able to yield a lower water/cement ratio makes the concrete more durable. However, if you are going to use the wet process, in order to achieve roughly the same result, you may use air-entraining agents. With the exception of accelerators, admixtures tend to be more user-friendly.
The dry process often produces pockets of rebound and lean mixture. The nozzleman needs to get rid of the low-quality shortcrete. This means that you may need to have an additional designated area for the waste materials.
These inconveniences and the hazards posed by dust happen less often during the wet process.
However, unlike the dry process, the wet process does not regularly yield compact concrete. Work can proceed even during windy condition with the wet process, unlike in the dry process. Lastly, thanks to the high-powered concrete pumps we have these days, it is now possible to lay concrete at a higher rate when using the wet process compared to the dry process.
Leave a Reply
You must be logged in to post a comment.