Concrete Pumping Contractor Fairbanks Ranch
Yes, It’s Possible: Trailer Pump Can Be Used for Concrete Pumping in Fairbanks Ranch
More and more information about concrete pumping in Fairbanks Ranch has become available, but there are particulars that need to be straightened out. However, in a rebuff to doubters, we have demonstrated that indeed it can be done.
Before we reveal how we made this possible, let us imagine a large hose with concrete flowing out on one end. Knowing how it moves will help you understand how you can use a trailer pump. Our team uses a priming agent to improve the viscosity of the mixture. In a test, we discovered that a mass comprising of three stones can slide easily through a hose with a three-inch diameter together with the portland cement, water and sand.
We concede that tests don’t always yield the same result as that produced in the actual process. During an actual concrete pumping operation, the process could be hindered by blockages inside the hose. Nevertheless, a three-inch hose should work out just fine if the pour is up to 150 feet only. But at 150 feet long, the hose delivered the concrete smoothly. To make sure that the stream of concrete would flow easily, you can use a hose with a diameter of four inches or greater.
Because the hose is heavier with the bigger volume of concrete flowing through it, the operator holding the tip of the hose may find it hard to keep it steady. In this case, having hooks will be of great help. Getting an extra pair of hands to pull the slack is also beneficial when it comes to weighty setups. As the load becomes heavier, more manpower will be required.
Opportunely, we are here to be of assistance to you in your projects. We know these things because we are specialists in rock concrete pumping. Our team specializes in providing concrete pumping for big rocks. We have the skills plus the equipment needed to handle your requests.
Concrete Pumping in Fairbanks Ranch Done Professionally
Go ahead, take your sweet time going over our online site, and you will see that we specialize in residential and commercial projects, and we accept industrial contracts, too. We have been in the construction business for over 20 years and have trained an elite group of operators who have worked on numerous projects using trailer pumps. The best part of our service is we do it fully insured so you can keep your peace of mind.
Our team of professionals will make sure that correct procedures are followed during the concrete pumping to assure the safety of everyone in the project site. Besides concrete pumping, we can also set up house lintels, tie beams, sauna tubes, preform columns, sink holes, power jacking, and slabs. Using our durable and high-quality line pumps, we can deliver concrete mixed with grout, rock, or pea rock in sizes up to one inch in diameter.
Long Distance, Big Rock Concrete Pumping
The minimum length of hose we usually offer is 200 feet, which is more than enough for most projects. But, we also have the means to cover longer lengths, some measuring up to 1,250 feet. We mostly use hydraulic trailer pumps for long distance and big rock concrete pumping projects, which have the capability to pump 70 cubic yards an hour.
Call us and our team will sit down with you to talk about your specific requirements. Be it for decorative purposes or to strengthen commercial or residential foundations, our certified experts can handle the job with utmost efficiency. We have many years of experience behind our back, and we are confident that we can deliver your retaining wall requirements to your satisfaction.
House Lintel Pumping
Our price covers 50 boards on the walls, and these can provide about 50 clean outs, We can also provide an estimate for larger requirements; you only have to inform us, and we will talk about your specific requirements further. We always make it mandatory to check the down cells if they can handle the filling. Then, we put the mixer in place and our technicians carefully inspect the truss straps. With ‘j bolts’ carefully placed in the garage header, and the wall and ground scraped. Rest assured that we will not take off the boards and the nails without a thorough look at the inspection hole.
Columns, Slabs, Tie Beams, Preform Columns, and Sauna Tubes
Our professional concrete placement team will work closely with you and your contractors to ensure foolproof and affordable solutions.
Power Jacking and Sink Holes
Our pumps come in different power capacities, the most powerful of them all yield a power of 4,000 PSI for void filling of the highest quality. It does not matter if the void is under a slab or beneath a building, we have the knowledge, the skill, and the equipment to treat the problem.
There is absolutely nothing simple about concrete pumping. It matters greatly to have the most modern equipment, and the proper knowledge to use such equipment. Concrete Pumping Services is your No. 1 choice when you want proven results. We have a full range of equipment to meet your specific needs, and our incredible team of professionals is always available to deliver the service that you require.
Concrete Pumping Services in Fairbanks Ranch: Why You Need Us
Concrete Pumping Services has all positive attributes in a company—broad experience, state-of-the-art equipment, and highly skilled professional technicians. We have been in this business for so many years, and this experience has propelled us to give you the best possible service. We do not only boast of a top-of-the-line equipment as we are also very proud of suitable training we provide our employees to give you your requirements with safety as main consideration. Give us a call if there is anything you need which concrete pumping can fulfill, and we will make sure to give you the best service you deserve. This has been our commitment from day one, and up to this very day, we remain true to our word. Go ahead and dial our number, or shoot us an email about your concerns; we are only too happy to discuss this in detail with you!
Concrete Pumping Service in Fairbanks Ranch: Best Equipment, Best Manpower
We opened our business with only one goal in mind, and that is to give our clientele the best possible service in terms of concrete pumping needs. Over the past years, we have persistently improved our services from day to day. That is why you can always expect top-notch concrete pumping services from us. Besides making sure we invest in the latest technology, we also make it part of our business to equip our personnel with the proper knowledge and skills to carry out their tasks safely and efficiently.
What We Offer
We take pride in having powerful state-of-the-art pumps in the hands of highly trained experts who are able to provide services that will even exceed your expectations. You need not worry about machine breakdowns slowing down your project. We have a well-equipped repair facility that can quickly restore machines to their prime condition. We offer different models of trailer pumps. Some of the models we offer includes Reed, Schwing, Putzmeister and Mayco. In case one pump develops problems, we always have a replacement unit that can be used to prevent work stoppage and project delays. Because of their broad experience, our specialists have figured out how to resolve issues at the slightest sign of trouble. We also have backup equipment to ensure that we can deliver our services on time. Over the years, our team has experienced working with a wide range of situations. Be it a repair or a concrete pumping request, you can count on us to deliver best-value deals.
Above all these, we offer you peace of minds as we are fully insured for the protection of all parties. So, sit back, relax and let us do all the hard stuff for you. So, really, there is nothing to worry about when you have us serving your concrete pumping needs!
Our Trailer Pumps Can Deal with Big Rock
Some people think we’re just boasting when we discuss our use of trailer pumps for delivering concrete to a project site. They can’t seem to understand that this is possible. They say only concrete boom pumps can deal with big rock. They say only concrete boom pumps can deal with big rock. Although it is true that boom pumps can do that, these pumps have one noteworthy shortcoming: Their outriggers consume a lot of space.
However, they have one major flaw: Their outriggers take plenty of space. Hence, we advise using trailer pumps instead. Trailer mounted concreate pumps are very economical and they work like a charm.
Trailer Pump Power
Trailer pumps are actually perfect when you’re working on fixing up either a commercial building or residential space. Why? It’s because these equipment pumps as much as 1,000 feet horizontally and 300 feet vertically. They can even work with as much as 70 cubic yards an hour in nearly all cases. While a model may slightly differ from one to the other, it’s likely that they come with the same boom pumps to pump kits and may weigh as much as 10,000 pounds.
Benefits of the Trailer Pump
A considerable number of our clients have shifted to using our trailer pumps instead of boom pumps even if they have the space in their project sites for those big machines. They have realized the many benefits offered by trailer pumps. First of all, they are easier to operate. They also leave minimal waste.
You see, with boom pumps, a large amount of concrete is left behind, converting to around one yard of waste material. Taking it out of the unit usually requires $160 every time. It does not appear practical, if we have to say it, especially if you consider the cost of the unit itself.
With a trailer pump, on the other hand, the waste materials are not that much, which means you get more for your project.
Decision is Up To You
The decision on whether to use boom pump or trailer pump is of course up to you. All modern concrete pumps are marvelous equipment. In the last 20 years, technological improvements have made these pumps more powerful and yield better results. Things have changed a lot since the early years of concrete pumps. So it will now just boil down to how much you can afford and whether or not your space is suitable for your choice of concrete pump.
Gunite versus Shotcrete
Gunite is a material that has been used for a considerable length of time in building pools. The material leaves the nozzle as a pressed wet aggregate that sticks to walls. The concrete mixture is pushed through the tube using pressurized air. Water needs to be added to the tip of the nozzle in order to control the flow better. The wet mixture passes through the nozzle and sticks to the wall where it is sprayed.
Because of this method of application, gunite experiences different issues. The quality of the blend depends completely on the precision of the onsite technicians. There are no precise controls or procedures to guarantee a reliable, steady and exact mixture.
Deviation, no matter how small, in the mixing of dry materials and water causes a reduction in the pressure rating, which is set at 2,000 psi. If there are problems with the consistency of the mixture, chances are the pressure ratings will be less than the recommended 2,000 psi.
Shotcrete is the solution to this gunite issue.
Instead of relying on the workers to cook the correct mixture of the dry and liquid materials, the manufacturer will handle the blending process through the use of accurate measurements from the computer back at the plant. That means every shotcrete that comes out of the plant is produced at the exact measurements. The portions are thoroughly regulated by a program so each truckload contains the perfect ratio of ingredients. The concrete dry mix is then combined with water and pumped via a two-inch sized hose with an air ring.
The latter is the preferred method of new construction today. In fact, the California Department of Transportation has ordered that only shotcrete will be used in roads, bridges and retrofits. The mixture can also be used in making pools since it can maintain up to 4,000 psi which helps prevent water leaks.
Most of our projects involve residential pools. We have constructed and repaired countless of pools in San Diego, all with astounding results. Over the years, other contractors have seen what we already know: Shotcrete is much superior to gunite.
Homeowners who wish to subcontract their pool project may also approach us for assistance. We are always willing to provide expert advice if you ask, and if you want some clarifications about shotcrete, feel free to tell us. We provided answers that satisfied them, encouraging them to choose us as partners in their projects.
Pool construction has seen major improvements through the years. Some of the newly built facilities have high-tech features such as vanishing edges, waterfalls, and artificial rocks. Our company has been showing the way in this regard. Our guidance has been sought by many pool developers and property owners who have known of our capability to produce the best results even in the most difficult conditions. Do you need proof of our quality workmanship? Well, you only have to look at our long line of clients to believe!
Drainage ditches are made to minimize water buildup in a property. In most cases, drainage ditches have a six-inch concrete lining. Most of the drain ditches for residential properties measure two feet wide and one foot deep. There is also a type D ditch, measuring 3 feet wide, and there is the trapezoid ditch, as well, that is recommended for commercial use. The volume of water blended with the concrete is very important in constructing these ditches.
For commercial and agricultural applications, such as for irrigation for instance, drainage ditches may range from three-foot wide to a width of as much as seven feet, along with a three-foot depth. After digging the ground, our personnel will place either a 6x6x10x10 wire mesh or 17-gauge wire mesh depending on the specified requirements. Our shotcrete team will then apply the concrete into the walls of the ditch.
In addition to making pools, we are also excellent in helping our clients control erosion in their properties. We are experienced in working with sloped properties. We also engage in erosion control in basements and underneath houses and other structures to keep water from undermining their foundations. Some slopes are in nearly vertical walls where we apply shotcrete with a rough nozzle finish that conforms to the shape of the slope. There are also slopes with very steep inclines that they are almost vertical. But we’ve used the methods that we designed particularly for these situations.
Shotcrete or Gunite?
Overall, gunite has taken a backseat to shotcrete in terms of efficiency and stability. But gunite can also serve its purpose in select projects because the procedure is cheaper, at least initially. We also use the newly created “Redi-set cement” in the shotcreting process. Ordinarily, newly applied cement with no droppings can support itself without inclining or peeling off.
There is little distinction between guniting and shotcreting. Gunite was first used in the early 1900s. The procedure used air pressure to apply mortar on walls that were considerably less thick than today’s structures.
The material becomes tightly packed upon impact. Set accelerators may, at times, be used to help with overhead placing. The new product, “Redi-set cement” may also be used in shotcreting. The dry-mix type of shotcrete is considered more durable and the one preferred by most users. Although the process can be classified under wet-mix and dry-mix, the latter procedure has become the preferred option for contractors.
The dry-mix procedure is as follows:
(a) Mix the cement and sand thoroughly.
(b) The mixture is then placed into a device called a “gun”.
(c) The feed wheel within the gun meters the mixture.
(d) The compressed air carries the material to a special nozzle through the delivery hose. Through the nozzle’s perforated manifold, the water is sprayed to combine wih the mixture of sand and cement.
(e) The resulting wet mortar is released from the nozzle at high velocity to be gunited.
The Wet-Mix Process and Application
In the wet-mix process, the concrete is mixed with water just like in normal cement mixing. It is then placed in the transport pipeline to the nozzle, where it is propelled by compressed air at high pressure into the surface.
The wet-mix procedure is no longer used as much today as it has been found to yield less successful results compared to the dry-mix procedure. High velocity or low velocity works well in the dry-mix process. The high-velocity gunite, which has a velocity of 90 to 120 meters per second, is produced with the aid of a small nozzle and high pressure. This produces good compaction results.
Advantages and Disadvantages of Wet and Dry Process
In the wet process, you can be able to accurately control the ratio of water to cement, but the ratio must not be too low, an issue that is better addressed by the dry process.
It is complicated to pump light-weight aggregate concrete so the dry method is more recommended by experts. However, if you want to avoid blockage issues, then you may use wet method. In the dry technique, wet sand often blocks the flow of the mixture, which could affect the air pressure inside the hose.
The fact that the dry process is able to yield a lower water/cement ratio makes the concrete more durable. However, if you are going to use the wet process, in order to achieve roughly the same result, you may use air-entraining agents. With the exception of accelerators, admixtures tend to be more user-friendly.
Nonetheless, air-conveying agents can be used to improve the strength of concrete that passed through the wet process. In general, admixtures can be used more advantageously in the wet process.
Even though the wet mix technique will help you avoid more waste materials and dust hazard, you will not be able to get a dense mortar, unlike if you use the dry method.
The personal nuisance and hazards caused by dust in the air during the dry process are experienced less often by technicians during the wet process. However, unlike the dry process, the wet process does not consistently produce compact concrete. The wet mix procedure will allow you to lay the concrete faster during a windy weather as compared to the dry method.
Leave a Reply
You must be logged in to post a comment.